久久久精品无码专区不卡_国产成人无码精品一区在线观看_精品无码久久久久久国产_亚洲国产综合无码一区

1. Save raw materials and reduce costs. 2. Shorten the forming cycle and improve the machine efficiency 3. Improve the surface quality and mechanical prop……

Discussion on the application of hot runner temperature control box in the system 1, the temperature control box is the temperature control of the hot runner, so as to better make the hot runner produce benefits. 2. The control principle of the temp

The hot runner temperature control box is the thermostat of the hot runner. The hot runner temperature control box is a kind of equipment which can continuously maintain the required temperature of the hot runner system. It consists of temperature control

A hot runner is a heating method that ensures that the plastic flows and the gate remains molten. The hot runner system usually consists of a hot nozzle, a split plate, a temperature control box and accessories. Hot nozzles usually include two types: open

Hot runner temperature control box is used to control the balance of the hot runner temperature control box controller, the internal temperature of hot runner system is necessary because it is over, because "the four interdependent with hot runner sy

1. Advantages of hot runner system: Save plastic material: in the pure hot runner mold because there is no cold runner, so there is no production waste. This……

The injection mold is composed of several pieces of steel plate, each part is different, basically divided into: 1. Ejector system (thimble, ejector bar) 2. Positioning device (guide post, guide sleeve) 3. Fixture (I plate, mold hole)4. Formi

熱流道系統的優點是什么： 1.當產品的壁厚較薄時，確保熔體可以完全到達遠離澆口的部分（橡膠入口），大大降低了產品的變形程度，并大大提高了表面質量和稠度產品； 2，熱流道系統流道內的壓力損失小，熔體流動良好，密度容易均勻，避免了變形，批峰，尺寸不穩定性，色差等缺陷。注塑零件； 3，消除全部或大部分材料（……

Hot runner system usually consists of hot nozzle, baffle, temperature control box and accessories. Hot nozzles usually include hot nozzle type, pouring sleeve type and valve type. The splitter plate is used for multi - cavity or multi - point feed or s

1.PID self-tuning function ensures the accuracy of continuous temperature control and high power double input and output. 2. The latest electronic circui……

高低溫沖擊試驗箱在運行時會發出聲音，但一般體積不大，對周圍環境的沖擊也不嚴重。但是，如果設備發出很大的噪音，則需要及時進行處理。如何應對高低溫沖擊試驗箱的噪聲？ 如果長期處于噪聲環境中，會對人體產生不良影響，因此根據國家標準規定，高低溫箱必須將噪聲控制在80 db以下，因此大多數高低溫沖擊……

No runner feed injection mold The so-called no runner condensate mold is in the injection molding, the molten material in the runner always maintains the hot flow state. When the mold is opened, only the solidified product needs to be taken out, an